How to put the belt on a kirby vacuum cleaner?
How to put the belt on a kirby vacuum cleaner?
?You've just bought a new Kirby vacuum cleaner. It's all put together and ready to go, but there's one thing left to do - put the belt on.

This might seem like a daunting task, but don't worry - in this article, we'll show you step by step how to put the belt on your Kirby vacuum cleaner.

Open the bag door

There are two ways to open the bag door on your Kirby vacuum cleaner. The first way is to press the release button on the top of the machine, near the handle. This will release the door, and you can simply lift it up. The second way is to use a screwdriver to remove the two screws that hold the door in place. Once these are removed, you can lift the door off.

Remove the old belt

1. Unplug your Kirby vacuum cleaner from the socket.
2. Remove the bag and empty it.
3. Find the two screws that hold the bottom plate in place and remove them with a Phillips screwdriver.
4. Put your hand under the bottom plate and feel for the old belt.
5. Pull the old belt off of the roller and throw it away.

Find the correct replacement belt

If your Kirby vacuum cleaner is no longer working as efficiently as it once did, it may be time to replace the belt. Fortunately, this is a relatively easy process that you can do at home. Here's what you need to know about how to put the belt on a Kirby Wet&Dry vacuum cleaner.

First, you'll need to purchase the correct replacement belt for your model of Kirby vacuum. You can find this information in the owner's manual or by contacting Kirby customer service. Once you have the correct belt, simply thread it around the pulleys on the vacuum cleaner according to the instructions in your owner's manual.

If you're having difficulty putting the belt on, there are a few tricks that can make it easier. First, try holding the ends of the belt with a pair of pliers. This will give you more control and make it easier to thread the belt around the pulleys. Another helpful tip is to use a piece of string or dental floss to thread the belt through the pulleys. This can be especially helpful if the belt is stiff or difficult to maneuver.

With a little patience and some careful planning, changing the belt on your Kirby vacuum cleaner is a fairly simple task. By following these tips


image source:

Install the new belt

1. Unplug the Kirby vacuum cleaner.
2. Remove the old belt from around the roller brush.
3. Remove the belt from around the motor shaft.
4. Install the new belt around the roller brush, making sure that it is tight.
5. Install the new belt around the motor shaft, making sure that it is tight.
6. Reattach the cover to the roller brush.
7. Plug in the Kirby vacuum cleaner and turn it on to test.

Close the bag door

The first step is to close the bag door. If the door is not closed, the vacuum will not work properly. To close the door, simply push it shut.

Next, locate the belt. The belt is located under the vacuum's power head. To access the belt, you will need to remove the power head. To do this, press the release button on the power head and then lift it off of the vacuum.

Once the power head is removed, you should be able to see the belt. If the belt is broken, you will need to replace it with a new one. To put a new belt on, simply thread it around the pulleys and then snap it into place.

Finally, reattach the power head and turn on the vacuum. The belt should now be working properly.

Test the vacuum cleaner

Assuming you have a Kirby vacuum cleaner, the following are the Vacuum cleaner Supplier instructions on how to put the belt on correctly.

First, make sure that the power is off and disconnect the vacuum from the power source. Loosen the screws that hold the bottom plate in place with a Phillips screwdriver. Remove the bottom plate carefully.

Locate the brushroll inside the vacuum cleaner and note how it is positioned. There should be a white cogwheel on one end of the brushroll. The belt will go around this cogwheel.

Remove any old belts from the brushroll and discard them. Take the new belt and thread it around the white cogwheel. Make sure that you position the belt so that it runs smoothly over all of the teeth on the cogwheel.

Now, carefully replace the bottom plate and screw it back into place. Reconnect the vacuum to its power source and turn it on. The new belt should be running smoothly around the brushroll.


image source:


So there you have it, a step-by-step guide on how to put the belt on a Kirby Handheld vacuum cleaner. We hope you found this helpful and that your vacuum is now up and running again. If you have any other questions or would like to share your own tips, feel free to leave a comment below.